亚洲情综合五月天-久久99国产精一区二区三区-久久天天躁夜夜躁狠狠85-成人免费看黄网站yyy456-日韩欧美群交p片內射中文-久久99热这里只频精品6

How to operate and maintain the valve during operation

Column:Technical article Time:2018-04-20
The principle of maintenance during the operation of the valve is as follows: 1 Keep the outside of the valve and the active part clean and protect the integrity of the valve paint. The surface of the valve, trapezoidal threads on the stem ...

The principle of maintenance during valve operation is as follows:
    1 Keep the outside of the valve and the active part clean and protect the integrity of the valve paint. The surface of the valve, the trapezoidal thread on the stem and stem nut, the sliding portion of the stem nut and the bracket, and the gears, worm gears and other components are likely to deposit a lot of dirt, oil, dirt, and other residues on the media, causing wear and corrosion to the valve. Therefore, you should always keep the valve clean. The general dust on the valve is suitable for brush sweeping and compressed air purging, and can even be scrubbed with a copper wire brush until the processing surface and mating surface show a metallic luster, and the paint surface shows the true nature of the paint. Steam trap should be specially responsible, at least once per shift; regularly open the flush valve and steam trap at the bottom silk plug flushing, or regularly disassembled to flush, so as to prevent dirt from clogging the valve.
    2 Keep valve lubrication, valve trapezoidal thread, stem nut and the sliding part of the bracket, bearing position, gear and worm gear meshing parts and other joint activities require good lubrication conditions, reduce friction between each other, to avoid mutual wear . For parts that do not have oil cups or nipples and that are easily damaged or lost during operation, the lubrication system should be repaired and the lubrication system must be repaired.
Lubrication parts should be regularly refueled according to specific conditions. Frequently opened, high-temperature valves are suitable for intervals of one week to one month; infrequently opened, low-temperature valves can have longer refueling cycles. Lubricant organic oil, butter, molybdenum disulfide and graphite. Oil is not suitable for high-temperature valves; butter is not very suitable, and they are lost due to high temperature melting. The high temperature valve is suitable for adding molybdenum disulfide and rubbing graphite powder. Exposure to the outside of the lubrication parts, such as trapezoidal thread, between the teeth and other parts if you use butter and other oils, easily contaminated with dust, and the use of molybdenum disulfide and graphite powder lubrication is not easy to contaminate the dust and lubrication effect is better than butter, graphite powder is not easy Apply directly, use a little oil or water to adjust the paste to use.
Oil-filled, sealed plug valves should be filled with oil for a specified period of time, otherwise they are susceptible to wear and leakage.
    3 Keep two complete and intact. The bolts of flanges and brackets should be complete and fully buckled. No looseness is allowed. The tightening nut on the hand wheel should be tightened in time to avoid wearing the joint or losing the hand wheel. After the handwheel is lost, it is not allowed to replace the handwheel with a flap. It should be promptly filled. Packing pressure difference does not allow skew or no pre-tightening gap. In the environment that is easily contaminated by rain, snow, dust, and other dirt, the valve stem must be equipped with a protective cover. The scale on the valve should remain intact and accurate. Valve seals, caps, pneumatic accessories, etc. should be complete and complete. The insulation jacket should be free from dents and cracks.
    In addition, it is not allowed to tap, support heavy objects or stand on the valve to avoid contaminating the valve and damaging the valve. In particular, non-metallic mesh doors and cast iron valves are even more forbidden.
    Maintain the daily maintenance of the electric device. The maintenance of electric devices is generally not less than once a month. Maintenance contents include: appearance should be clean, no dust accumulation, the device is not contaminated by soda, oil; sealing surface, points should be solid and tight. No leakage phenomenon; Lubrication parts should be refueled according to regulations, Valve Xuan nuts should be greased; Electrical parts should be intact, no phase failures, automatic switches and thermal relays should not trip, indicating light is correct.

主站蜘蛛池模板: 色综合日韩| 少妇精品无码一区二区免费视频 | 狠狠色噜噜狠狠狠狠2021| 香蕉视频在线观看免费国产婷婷| 蜜臀av色欲a片无人一区| 12av毛片| www.色婷婷| 天天爽夜夜爽人人爽曰| 中文字幕av网| 99视频精品全部免费 在线 | 人妻夜夜爽天天爽| 久久婷婷色| 久久久久国产精品嫩草影院| 亚洲欧洲日产国码在线观看| 黑人大战中国av女叫惨了| 亚洲人网站| 老牛影视av一区二区在线观看| 又大又硬又爽免费视频| ww1515hh海外永久360| 午夜裸体性播放| 亚洲福利视频网| 人人爽人人澡人人人妻| 亚洲一区二区欧美| 不卡在线一区| 欧美午夜在线| 欧美精品videossex少妇| 欧美福利| 9999网站| 国产午夜福利短视频| 91综合网| 久久久久久国产精品视频| 人妻无码久久中文字幕专区| 日韩在线欧美| 三级在线网站| 夜夜操狠狠干| 亚洲色爱图小说专区| 亚洲精品66| 日本高清免费zzzzzzzz| 人妻三级日本香港三级极97| 欧美jizzjizz在线播放| 亚洲国产欧美91|